Try to make Fedora17 run on Beaglebone – 1

For now, my SD card include Angstrom Boot files and Fedora 17 Root files.

Connect BeagleBone(inserted SD card) to my desktop(F17),  can’t find any partition mounted.

Use command # screen /dev/ttyUSB1 115200, try to connect BeagleBone.
conncet to U-Boot     Which is not right.

 

Found the F17 OMAP Kernel of beagleboard xm (Page:http://fedoraproject.org/wiki/Architectures/ARM/Fedora_17_GA ,Download: http://download.fedoraproject.org/pub/fedora-secondary/releases/17/Images/armhfp/Fedora-17-armhfp-beagle-mmcblk0-kernel.tar.xz)  and try to replace this uImage file to Angstrom uImage files on Boot partition.
After replace the file, try to boot up.

Here is the connection message:

Reset BeagelBone
[root@Fedora17 jcqiu]# dmesg | tail
[ 6129.268191] usb 2-5.1: Setting MaxPacketSize 512
[ 6129.268478] usb 2-5.1: FTDI USB Serial Device converter now attached to ttyUSB1
[ 6129.268487] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 6144.230016] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 6144.231743] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 6144.231747] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 6148.680082] usb 2-1: reset high-speed USB device number 2 using ehci_hcd
[ 6196.964515] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 6196.966024] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 6196.966028] sd 4:0:0:0: [sdb] Assuming drive cache: write through

display later
[root@Fedora17 jcqiu]# dmesg | tail
[ 7189.327082] usb 2-1: reset high-speed USB device number 2 using ehci_hcd
[ 7241.444261] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7241.445762] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7241.445765] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 7293.668900] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7293.670389] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7293.670393] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 7345.892655] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7345.894149] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7345.894153] sd 4:0:0:0: [sdb] Assuming drive cache: write through

Disconnect from Computer
[root@Fedora17 jcqiu]# dmesg | tail
[ 7398.233054] usb 2-1: reset high-speed USB device number 2 using ehci_hcd
[ 7450.340430] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7450.341938] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7450.341942] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 7477.193331] usb 2-5: USB disconnect, device number 4
[ 7477.193335] usb 2-5.1: USB disconnect, device number 5
[ 7477.193637] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 7477.193653] ftdi_sio 2-5.1:1.0: device disconnected
[ 7477.193945] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
[ 7477.193961] ftdi_sio 2-5.1:1.1: device disconnected

Reconnect
[root@Fedora17 jcqiu]# dmesg | tail
[ 7505.084988] usb 2-5.1: Endpoint 2 MaxPacketSize 512
[ 7505.084991] usb 2-5.1: Setting MaxPacketSize 512
[ 7505.085434] usb 2-5.1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 7505.087570] ftdi_sio 2-5.1:1.1: FTDI USB Serial Device converter detected
[ 7505.087596] usb 2-5.1: Detected FT2232H
[ 7505.087598] usb 2-5.1: Number of endpoints 2
[ 7505.087601] usb 2-5.1: Endpoint 1 MaxPacketSize 512
[ 7505.087604] usb 2-5.1: Endpoint 2 MaxPacketSize 512
[ 7505.087606] usb 2-5.1: Setting MaxPacketSize 512
[ 7505.087859] usb 2-5.1: FTDI USB Serial Device converter now attached to ttyUSB1

display later
[root@Fedora17 jcqiu]#
[root@Fedora17 jcqiu]# dmesg | tail
[ 7607.012492] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7607.014012] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7607.014016] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 7659.236512] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7659.237993] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7659.237997] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 7659.346068] usb 2-1: reset high-speed USB device number 2 using ehci_hcd
[ 7711.460489] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 7711.461972] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 7711.461976] sd 4:0:0:0: [sdb] Assuming drive cache: write through

 

Still cannot booting up success, I probably will try to use the f18.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s